|
ProFormer
Metal Forming Tools for the Professional
Made in the USA
" More than 50 Sheet Metal
Brake Models to choose from"
|
Contents |
|
Straight Brakes . . . . . . . .
.Over 25 ProFormer Straight
Brakes Models |
|
Finger Brakes . . . . . . . . .
.Over 30 ProFormer Finger
Brakes Models |
|
Hydraulic Assist . . . . . . .
.Hydraulic Assist for Sheet Metal Brakes |
|
Brake Options . . . . . . . . .
.Customize your brake for the work you do! |
|
Radius Brakes . . . . . . . . .
Your answer to forming radius bends! Four Models |
|
Stretcher Shrinker . . . . . .
Cast iron bodies and hardened tool steel jaws! |
ProFormer Straight Brakes
Over 25
ProFormer Straight Brakes to choose from.
Widths from 3ft to 10ft and 22 to 12 gauge.
ProFormer Straight
Brakes come in Heavy Duty S Series and
Industrial Class L Series
ProFormer Finger Brakes
Over 30
ProFormer Finger Brakes to choose from.
Widths from 3ft to 10ft and 20 to 12 gauge.
ProFormer Finger
Brakes come in Heavy Duty BP Series,
Industrial Class U Series and Extra Deep Box C
Series.
The Extra Deep model allows forming boxes up to 6 inch deep.
ProFormer Radius Brakes
It's FAST It's CONSISTENT It's your
answer to forming radius bends!
The apron swings OUTSIDE the radius and it ROLLS to minimize
stress and scraping on your material.
Comes with 5 radii from ½” radius (= 1” diameter) through 2”
radius (= 4” diameter) Other radii are available.
Note: Radius equals one half the diameter.
Truly unique.
Two most popular models are 6’ and 8’
ProFormer
SHEET METAL BRAKES HAVE MORE STANDARD FEATURES
Designed and built for the long run: you can
rebuild clamp and apron assemblies, vertical guides, cams,
apron hinge pins or bushings. Entire top clamp assemblies or
nose bars can be replaced. For BP & U Models, replacement
finger sets are very reasonably priced.
Minimum reverse bend for all models is 1/2",
OR 1/4" minimum reverse bend may be ordered on all models.
Beam adjustment. (Maximum clamp setback)
for all models is 1" Additional setback my be ordered.
Heavy Struts Rods under table, on & behind
clamp, and under aprons are adjustable so you can maintain
true centers.
Center leg included with all 8 & 10 ft
models and some 4 to 6 ft models, may be installed for
easier hemming while minimizing need to preload struts. The
result is easier hemming and less wear on you and your
brake.
S & L Straight Brake Models have openings at clamp
ends allowing you to form 3 sides of a pan to depth shown in
the chart (see ProFormer Straight Brakes) under "Max Depth
of Box".
BP & U Model Finger Widths, depending on the model,
one or two 2", two or three 3", and the rest 4". Or you
may specify the widths and mix. A spare 4"
finger is included with all U models, and is
optional on BP models. Use it to cut a slot at an odd width,
like 3/4" or 1-3/8". Additional spares and complete sets are
so inexpensive you may want several for experimenting. Many
BP and U models are available with long fingers allowing box
depths up to 6". Each finger is individually adjustable for
leading edge alignment, greatly increasing useful life of
the set.
SPECIAL 4" CUT BACK FINGER to bend up to 4" of 3/16"
mild steel w/o adjusting set back or clamp
pressure (or damaging one of the "good" fingers), is
included with all U model, and is optional for 16ga BP
models.
Even though all
ProFormer brakes come with a
long list of standard features at no additional cost,
ProFormer is always looking for new ways to make their
brakes more versatile to fit everyone's needs.
With over 16 options available, please check the
ProFormer
Options page to see if there is an option you may
want to add to customize your brake for the work you do.
|
ProFormer
Hydraulic Assist |
With the
ProFormer Hydraulic Assist you can bend 10' of 12ga by
yourself in about 15 seconds. Your choice of a frame mounted
switch or optional foot operated switch. This system can
also be added to any existing ProFormer sheet metal brake
listed above.
|
ProFormer
Stretcher
Shrinker |
Small,
portable and light weight. No welding, heating or hammering
necessary. Use it to help make wheel wells, radiator
shrouds, door jams or many hard to form combination of
curves and angles. Can be bought as One body with two jaws
(combo) or as shown on optional stand with two separate
bodies.
|
We are sorry to announce that ProFormer is no longer in business.
We CAN provide you with alternative brakes and equipment with the
Quality & Pricing to fit your application and budget. Please
contact us so that we can assist you. |
